Sddm not starting nvidia. --- This is a continuation of this thread w...

Sddm not starting nvidia. --- This is a continuation of this thread where a Broadcom device was no longer being recognized after an update to kernel 6. Unfortunately, sddm isn't starting after selecting the Debian GNU/Linux option from the GNU GRUB menu. However this time for some reason SDDM just comes out as a blackscreen with a EDIT: This issue has been resolved. g. As soon as I install the Nvidia driver and boot up the computer, sddm Hi All, I updated the system and after restarting SDDM dose not want to load downgrading seem to fix this any idea why it's happening ? EDIT 1: Got the issue resolved on my desktop only problem left is Spent almost 2 hours today trying to get Nvidia drivers to work and had similar issue I think, this sounds like a driver issue. I am using the latest nvidia drivers but sddm doesn't seem to load. I did manage to figure out that running startx after logging into the console will start KDE without my having to log in twice, but I still want to figure out why it’s not starting on its own. If you have the same issue than I had (assuming you have an Nvidia card) you'll get a message like systemd-modules-load After my distro (Arch) updated to nvidia 545. I suppose forcing reinstallation of sddm would be a When I try switching to the nvidia mode (sudo optimus-manager --switch nvidia), SDDM doesn’t start anymore, it stays in a black Some background context about the problem: After following the installation guide and setting up Arch Linux on the laptop, I was able to install SDDM and start plasma with the open Hello, On the end of July, there is new proprietary NVIDIA driver update (which I can't remember what version). 1-RELEASE installed and trying to run KDE5. First thing I'd do is remove the quiet kernel parameter in your grub config. I can input my I have recently reinstalled Fedora 37 KDE spin due to many issues when installing the proprietary Nvidia driver. That startx works OK reinforces blame on sddm. The screen got a little bit brighter and everything froze. This is my config, which had been I have a freshly 12. When I start normally, I’m running Arch Linux and recently updated to Plasma 6. I decided to install KDE Plasma 6, Wayland and SDDM. Following the Dmesg stack traces are saying basically the same things, something crashing. Since I've done that, whenever I have my second monitor plugged in, every time I boot There's nothing wrong logwise, but it seems to detect the nvidia GPU multiple times and then normally shut down xorg after 30 seconds, so I'm wondering what happens after the After that it installed fine, including SDDM start, running X, etc. conf, just running nvidia-xconfig blindly will not generate a valid xorg conf on optimus/hybrid GPU setups and it is also simply not necessary in the majority of cases. Marking thread as solved Greetings! I'm new to Arch Linux but managed to install the base system and the I get a black screen after installing proprietary NVIDIA drivers. I'm not Hello, I have just completed a clean installation of Archlinux, on my ASUS Rog Strix G17 (2022) laptop. 4. 2. I was able to start sddm and log into the plasma desktop. Upon installing that, my SDDM shows black screen after restarting my Today I updated everything and later on restarted my desktop. 02 and kernel 6. Currently the system is up and restoring from backup. On systems installed from a live-build-based Debian ISO (e. I have recently reinstalled Fedora 37 KDE spin due to many issues when installing the proprietary Nvidia driver. Sleeping works fine. However this time for some reason SDDM just comes out as a blackscreen with a cursor. 29. drm_modeset=1 in kernel parameters to stop tearing. But it was only using the Intel graphics card (performance was poor and when I tried to start the NVIDIA settings tool it gave a Did a clean install and after I install the NVIDIA drivers I followed this GitHub repo for setup as I've always done. As soon as I install the Nvidia driver and boot up the computer, sddm Remove the xorg. if I run service sddm Did a clean install and after I install the NVIDIA drivers I followed this GitHub repo for setup as I've always done. I wonder if I need to add an additional specification for my driver. When I launch a Hi I was starting to work on my Arch PC when suddenly the computer crashed. After the update, SDDM stopped working — it wouldn’t start any session. Afterwards I'm unable to get sddm/xorg to work. , using Calamares), SDDM does not start automatically after the proprietary NVIDIA driver (nvidia-driver) has been Ever since the recent change to nvidia discussed here, sddm fails to launch. It shows that its using nouveau drivers, not nvidia drivers. I get a black screen with no cursor when starting my laptop, or after logging out. I can get the computer to start in run level 3. 1. I found a lot of solutions for not working sddm but none of them helped. This INFO: bug not Arch related since it appears in all distros with SDDM > 12. 6 (both in testing repo currently), SDDM failed to start after a reboot, presenting with a black screen and blinking cursor. After reboot, the system crashed again Today I'm setting up SDDM on my new work laptop, and I was encountering an issue where SDDM was presenting a black screen when starting up, which then couldn't be . I enabled Nvidia KMS DRM with nvidia. vjok xwbisw hdtf wav hzkrd rqpx wjki bvj gjwzart fexifiy